Interplater hd85 thermal pdf. Thermal analysis and design enae d principles of space systems design u n i v e r s i t y o f maryland nonideal radiative. Service Manual + 68/85 Plate Processor InterPlater 85/ HD Polymer Service manual Plate Processor+ 68/85 .. Cleaning of developer heating element. Thermal Plate Processor Raptor 85/ Interplater HD 85 G&J used/refurbished. Glunz Jensen Interplater Plate Processor Model Perfect Condition.
|Country:||Antigua & Barbuda|
|Published (Last):||23 May 2016|
|PDF File Size:||2.58 Mb|
|ePub File Size:||8.75 Mb|
|Price:||Free* [*Free Regsitration Required]|
Labels with roller configuration T Mounting of rollers Inside the top cover is mounted a label showing the roller configuration. The LED is located near the 24 Vdc output connector.
Thermal energy can flow from one object to another by.
Mount the exit table. The filter s are placed ihterplater the processor in the right side and mounted in a drawer unit for easy access. For CTP Online processors the height and input height may have been changed in order to fit the setter height and thus not as illustrated.
It’s a community-based project imterplater helps to repair anything. Tighten with the filter key 3. X3,F to F10,1 Black: Replace any defective part. X3,B to F10,5 Orange: See illustration on the following page. Recycling The processor should be disposed at a certified appliance recycling centre or processing centre. A1 Main power distribution.
Wash T Wash water recirculation system. The rubber rollers 8 at the developer section entrance always run dry to ensure a homogeneous development. Manuals are available from the manuals link to the right.
Loosen the interpoater 1 and adjust the actuator 2 sidewards until it fits smoothly 3 into the switch 4.
How to read pdf files in my mobile
Functional description General Processor sections The processor contains six major sections, each performing a basic function to change the exposed plate into a fully developed and dry plate, ready for handling see illustration below.
F17 Transport motor M1 4AT, 6.
For cleaning and maintenance subjects see the processor user manual. Pressure is adjusted as shown on the illustration below. In the wash section the plate is washed on both sides by means of the spray tubes 13 and brushed on the upper side by means of the brush 14 optional.
Processor must turn off when set to “0”. Conveyor connection Not all models accessory equipment. Electrical Refer to the electrical diagrams in the back of this manual.
See the packing list s delivered with the equipment for further information. Level out the processor lengthwise by placing a spirit level on the left 4 and right 5 tank side. E this barrier is designed with strong 3hour performance in a moderate temperature range for powder paint. Press the upper roller into tuermal bearing by pressing the roller key upwards 3.
InterPlater 85/135 HD Thermal
CE Declaration of Conformity 4 Language: M13 is used on Rapzac processors. When mounting upper roller insert the roller key between the upper roller and the lower roller as shown 3.
Please note that processor without rollers, brushes, and heat sink model interpltaer weights app. The diagrams 4 pages cover: Make sure to lift the processor out of the holes 3 when lifting it down the pallet. The thermal impedance of the tim was measured using a new. Cleaning agents Never use cleaning agents containing chlorinated solvents, acetic or phosphoric acid.
InterPlater 85/ HD Service Manual |
Transport through narrow doorways Dependent interplateg the width of the door s through which the processor has to be transported to the installation site, the Service Technician may have to perform the actions described in the table below: The main power connection must be made in the field-wiring box located on the left side of the processor next to the hx85 cabinet.
Make sure that you obtain a uniform grip in both sides and in the middle. Incorrect storage may very well result in unsatisfactory processing quality etc. Setter interfaces If the processor is installed as an online system, you should now install the setter interface as described in the Interface Manual. Adjustment of the lid intreplater may be needed after leveling of the processor. Always read the Safety Instruction Manual part No before installing or operating the equipment.